Skip to main content
3D proof of a custom address concrete stamp reading "2847 CEDAR AVE S" pressed into concrete
3D proof from our designer. You approve your own proof before we cut.
Address marker

Put your house number in the concrete.

Type your house number and street, see the exact stamp, and press it into the new pour. The number becomes part of the slab, so there's nothing to peel, fade or blow away.

This stamp, as shown
$100
Order minimum · 26.0 × 6.0 in · shipping priced at checkout

“Design yours” opens your words in the free designer, where you choose the font and size. No account needed.

Before your pour

Order at least 4 weeks before your pour, or 3 with express shipping.

Production takes at least 10 business days, then standard shipping adds 5–7 business days. Express and overnight shipping are available at checkout.

Planning around a pour date?

Working out your dates…

An estimate for orders placed today. You choose the shipping speed at checkout, and the shop emails your ship date after purchase.

When do you press a house number into wet concrete?

Press it when the concrete is thumbprint-firm: the bleed water is gone, and your thumb leaves a clean 1/4-inch print without pulling up paste. That is typically 30 to 90 minutes after finishing.

Weather moves that window. On a hot, sunny day above 85°F it can shrink to 20 to 30 minutes. On a cool, overcast day between 50 and 65°F it can stretch to 2 to 4 hours. Test every 10 to 15 minutes near the spot where the number goes, not at the panel edge, because edges and thin spots set first.

If you're unsure, go early. A press that comes too soon can be floated out and done again. A press that comes too late tears the letter edges, and that can't be undone.

Read the full field guide

How big should the numbers be?

Use 3-inch numbers if people need to read them from the street. That is the largest size we cut. For a front walk read from a few feet away, the standard 1.75-inch letters are enough.

Letters can be up to 3 inches tall. The smallest depends on the font: 1 inch in DejaVu Sans Bold, 1.25 inches in most of the others. The designer shows the full stamp size as you type. A house number and street at the standard size, like our sample, comes to about 26 by 6 inches.

The price follows the stamp's area: 60¢ a square inch with a $100 minimum, so a short house number and street usually lands at the minimum. Type your own number at the top of this page to see the exact price.

Where should a house number go on a driveway?

Near the street end, out of the tire paths and away from the joints, within easy reach of a form edge. Reaching into the middle of a panel means kneeling boards and footprints to repair.

Decide which way it reads before the pour. Text should read right-side-up to the person coming toward it, so a number on a driveway usually faces the street. This is the one mistake with no fix, so check it again before you press.

The impression sits 1/4 inch below the surface. That is deep enough to read and shed water, and it leaves nothing raised for a snow shovel to catch or a foot to trip on.

Can a house number go on a curb or driveway apron?

Yes, if that concrete is being poured new and you have the city's permission. Measure first: our stamps are at least 6 inches in each direction, so a curb narrower than that won't take one.

The front walk is usually the easier spot. It's yours, it's wide enough, and visitors and delivery drivers pass it on the way to the door.

Do you need permission to put a house number in a public sidewalk?

Usually, yes. The public sidewalk, and often the curb and driveway apron, belongs to the city even when you pay for the repair. Call your public works department before you press anything there.

Your own driveway and front walk are yours to mark. Rules vary by city, so treat this as general information, not legal advice.

Can you add a house number to old concrete?

No. A stamp only works in fresh concrete, before it sets. For a slab that has already cured, the options are engraving, saw-cutting, or replacing the panel.

If a panel of your walk or driveway is due for repair, that new panel is your chance. Order the stamp ahead of the pour so it's on site when the crew finishes.

Who presses the stamp, you or your concrete contractor?

Either one. Many homeowners press the stamp themselves. If you're hiring out the pour, hand your contractor the stamp. The press takes under a minute and needs no special skill; the skill is in the pour and finish.

Tell the finisher about the stamp when the pour is scheduled, not when the truck shows up. The press lands in the busiest stretch of the job, so someone needs to own it. Quick steps come in the box, and the crew guide is emailed with every order as a PDF to hand over.


What you get

Stamp size (as shown)
26″ × 6″
Plate
Solid rigid plastic plate
Frame
Welded aluminum
Handles
Clip into brackets on the frame
Impression depth
0.25″ standard, or 0.125″ at the same price
Production
at least 10 business days
Made in
Minnesota, USA

Where it goes

  • New front walks and driveways
  • Curbs, for emergency crews and deliveries
  • Apartment and commercial entries
  • Contractors adding a finishing touch

Ways to set a house number.

Open any of these in the designer and make it yours.


FAQ

Questions, answered.

Does the number need paint to show up?
No. The impression reads on its own, and there's nothing applied to wear off. Seal the slab, or don't, as you normally would; the impression needs no special treatment.
Will it work on a broom finish?
Yes. Broom the panel first and press into the broomed surface. The impression reads crisply either way.
What else do I need on pour day?
A release agent made for stamped concrete, so the stamp lifts clean, plus an edging tool for touch-up and a bucket of water with a stiff brush to clean the stamp afterward. Add kneeling boards if the number sits away from an edge.
Can I press the same number twice?
Yes. Rinse the stamp, re-apply release agent and press again, so one stamp can mark both the driveway and the front walk. We can point to the record: stamps we cut more than 15 years ago are still in use in the field.
Can I change the number later?
No. Once the concrete sets, the impression is permanent. Check the digits on your proof before you order; you approve the exact stamp before we cut it.
What if my wording is longer or shorter?
The price is set by stamp size: $0.60 per square inch of stamp face, with a $100 minimum. Type your own words in the designer and the exact price updates as you type. Shipping is priced separately at checkout.
How fast will it arrive?
Production takes at least 10 business days from order confirmation, then it ships with tracking. Express and overnight shipping are available at checkout.

Keep reading

Other custom concrete stamps

The ground remembers.

Stamped Sidewalks, a Dimension Sign shop. Made in Minnesota.